• The YJ interior cage kit is finally available! Due to the age in these vehicles (rust) we have added a little extra in our cage kit to ensure your safety. Our kit is complete and includes seat mounting tubes and frame tie-ins. All the floor plates, bushings, and seat tabs are included with pre-bent and notched tubing. All you need to supply is the bolts for the cage plates. All tubing shown in the instructions is included – no extra cost for essential bracing! Our kit was made on a factory YJ with a 1-1/2” body lift and boat sides and used standard Corbeau fixed back seats. If you have a larger body lift – remove it! If you have no-body lift some trimming of the frame mounts may be necessary. If you don’t have boat sides that’s fine it will still fit. If you have different seats we recommend you upgrade to a fixed back seat and utilize the harness bar and seat mounting tubes for optimum safety. Other seats can be made to work but might not work with the X bracing behind the seat. We highly recommend that your seats be mounted to your cage properly and not the factory floor that is likely rusting away or highly modified.  Back seats are still useable but a bit more difficult to access due to the bracing. Main tubes are 1.75 x 0.120 wall DOM Smaller tubing is 1.5 and 1.25 for gusseting. We tried to included a bunch of  photos of our installations to help you with your installation but please read the instructions first.

    FREE SHIPPING IN THE U.S.

    THANKS TO SHIPPING COST INCREASES DURING PEAK SEASONS THERE IS AN ADDITIONAL FEE INCLUDED IN THE PRICE NOW – SORRY!!  WE ARE CONSTANTLY WORKING TO REDUCE COSTS BUT SHIPPING IS GETTING OUT OF HAND
    Jeep YJ Directions
    Kits are made to order and typically ship within 2 weeks of order unless in stock (We can't keep them in stock!).  Kits ship regular ground shipping to your door.  Tracking will be sent when your order is sent out.
  •   The XJ Cherokee hybrid cage kit is available for four-door models only but can be made to fit a two-door with some minor trimming.  The exterior part of the cage kit includes the roof hoop and a-pillar/windshield bars.  The Interior part of the kit includes the b/c/d pillars and bracing.  16 cage plates are included to sandwich the roof attaching the interior to the exterior cage as well as the interior cage to the sliders and unibody at the rear.  Sliders are necessary (No Longer an option we have time for) you can use any brand as long as there is adequate support for the a-pillar post.  Trimming will be required at this location. IMPORTANT – B PILLAR MUST BE TIED TO UNIBODY STIFFENERS Main tubes are 1.75 x 0.120 wall DOM Smaller tubing is 1.5 and 1.25 for gusseting. Please download and read the instructions below and contact us with any questions. Kits are made in small batches and we have yet to be able to keep up with demand and have them in stock.  Typical lead time is 2 weeks to ship.  All kits are shipped UPS Ground.
    THANKS TO SHIPPING COST INCREASES DURING PEAK SEASONS THERE IS AN ADDITIONAL FEE INCLUDED IN THE PRICE NOW - SORRY!!  WE ARE CONSTANTLY WORKING TO REDUCE COSTS BUT SHIPPING IS GETTING OUT OF HAND
    XJ Hybrid Instructions  
  • Introducing The Weld It Yourself RADIUS Cage Kit For The Can-am X3 MAX! This Cage Is Built With .120 Wall DOM Main Tubes And .095" DOM Support Tubing That Can Be Either MIG Or TIG Welded Without The Use Of A Specialized Fixture - Just Install The Supplied Connector Plates To The Stock Cage Locations And Piece Together The Cage On The Vehicle. INCLUDES
    • 24 Laser Cut Tube Pieces With Laser Etched Part Numbers On Each Component
    • 1.75" OD .120 Wall DOM Tubing For Main Hoops
    • 1.50" OD .095 Wall DOM Tubing For Windshield Cross Bars
    • Mounting Plates & Hardware To Mount In Factory Landing Locations
      REQUIRES
    • Welding - This Kit Can Be Welded Together Once Configured On The Vehicle
    UPGRADES
    • Aluminum Roof - .06 Thick 2 Piece Roof W/ Small Visor Bend And Bead Rolled Joint - Complete With Weld On Tabs And 1/4" Grade 8 Hardware
    NOTES
    • This Cage Sits 15.20" (38.60cm) Tall From B Pillar Mounting Plate To Highest Point On Cage
    • Late Model X3's Come With A Clamp Style Mount At The A-Pillar Landing Point - This Clamp Must Be Cut Off And The Supplied Flat Plate Will Be Installed In Its Place.
    • Must Use A Floor Jack Under Center Of Vehicle During Installation To "Level Out" The Frame Rails - Failure To Do So Will Make Aligning The Cage At The Factory Locations Difficult
    INSTALLATION VIDEO https://youtu.be/kZP8o3TTLag
  • Introducing the weld-it-yourself RADIUS cage kit for your 2014+ Polaris XP1000 4 Seater! This cage is built with .120" &  .095" DOM tubing that can be either MIG or TIG welded without the use of a specialized fixture - just install the supplied connectors to the stock cage locations and piece together the cage on the vehicle.   INCLUDES
    • 17 Laser cut tube pieces with laser-etched part numbers on each component
    • 1.75" OD .120 Wall DOM Tubing for main structure (2 piece main hoops)
    • 1.75" OD x .095 Wall For Main Structure Components & 1.50" OD x .095 Wall DOM Tubing For Windshield Cross Bars
    • (2) A Pillar & (4) B or C Pillar clamps to attach to OEM cage location
      REQUIRES
    • Welding - This kit can be welded together once configured on the vehicle
    UPGRADES
    • Aluminum Roof - .06 thick 2 piece roof w/ small visor bend & bead rolled connection - Complete with weld on tabs and 1/4" grade 8 hardware
    NOTES
    • Measuring from the frame mounting bolt on the B Pillar of your RZR to 42.60" will give you the total height of the LSK cage (See photo in product gallery)
    • Aluminum roof upgrade is a single piece of .06 aluminum with a slight visor bend up front to match the cage radius
  • Introducing The Weld It Yourself RADIUS Cage Kit For The Can-am X3! This Cage Is Built With .095" DOM Support Tubing That Can Be Either MIG Or TIG Welded Without The Use Of A Specialized Fixture - Just Install The Supplied Connector Plates To The Stock Cage Locations And Piece Together The Cage On The Vehicle. INCLUDES
    • 20 Laser Cut Tube Pieces With Laser Etched Part Numbers On Each Component
    • Made 1.75" & 1.50" .095 Wall DOM Tubing
    • Mounting Plates & Hardware To Mount In Factory Landing Locations
      REQUIRES
    • Welding - This Kit Can Be Welded Together Once Configured On The Vehicle
    UPGRADES
    • Aluminum Roof - .06 Thick Roof W/ Visor Bend - Complete With Weld On Tabs And 1/4" Button Head Hardware
    NOTES
    • Late Model X3's Come With A Clamp Style Mount At The A-Pillar Landing Point - This Clamp Must Be Cut Off And The Supplied Flat Plate Will Be Installed In Its Place.
    • The Shipping Box Is Quite Large For This Particular Model, It Is Recommended To Not Lift The Box On Your Own
    INSTALLATION VIDEO https://youtu.be/kBx7pvkXvYw
  • Introducing The Weld It Yourself RADIUS Cage Kit For Your 2014+ Polaris XP1000 2 Seater! This Cage Is Built With .095" DOM Tubing That Can Be Either MIG Or TIG Welded Without The Use Of A Specialized Fixture - Just Install The Supplied Connectors To The Stock Cage Locations And Piece Together The Cage On The Vehicle. INCLUDES
    • 17 Laser Cut Tube Pieces With Laser Etched Part Numbers On Each Component
    • 1.75" OD .095 Wall DOM Tubing For Main Structure
    • 1.50" OD .095 Wall DOM Tubing For Windshield Cross Bars
    • (2) A Pillar & (4) B Or C Pillar Clamps To Attach To OEM Cage Location
      REQUIRES
    • Welding - This Kit Can Be Welded Together Once Configured On The Vehicle
    UPGRADES
    • Aluminum Roof - .06 Thick Roof W/ Small Visor Bend - Complete With Weld On Tabs And 1/4" Grade 8 Hardware
    NOTES
    • This Cage Sits 19.7" (50.00cm) Tall From Center of Top B Pillar Mounting Bolt To Highest Point On Cage
    • Aluminum Roof Upgrade Is A Single Piece Of .06 Aluminum With A Slight Visor Bend Up Front To Match The Cage Radius
    INSTALLATION VIDEO
    • Installation Video Of RZR Flat Cage Below (Note: The Cage In The Video Is An OLD Style 2 Piece Main Hoop, Current Cage Is One Piece Hoops As Seen In Product Gallery)
  • Introducing The Weld It Yourself RADIUS Cage Kit For The Yamaha YXZ! This Cage Is Built With .095" DOM Tubing That Can Be Either MIG Or TIG Welded Without The Use Of A Specialized Fixture - Just Install The Supplied Connectors To The Stock Cage Locations And Piece Together The Cage On The Vehicle. INCLUDES
    • 17 Laser Cut Tube Pieces With Laser Etched Part Numbers On Each Component
    • 1.75" OD .095 Wall DOM Tubing For Main Structure
    • 1.50" OD .095 Wall DOM Tubing For Windshield Cross Bars
    • (4) A or C Pillar Clamps & (2) B Pillar Clamps To Attach To OEM Cage Location
    REQUIRES
    • Welding - This Kit Can Be Welded Together Once Configured On The Vehicle
    UPGRADES
    • Aluminum Roof - .06 Thick Roof W/ Small Visor Bend - Complete With Weld On Tabs And 1/4" Grade 8 Hardware
    NOTES
    • This Cage Sits 17.00" (41.27cm) Tall From Center Of B Pillar Through Bolt To Highest Point On Cage
    • Aluminum Roof Upgrade Is A Single Piece Of .06 Aluminum With A Slight Visor Bend Up Front To Match The Cage Radius
    • Harness Bar Measures A 1.5" OD Diameter
    INSTALLATION VIDEO
  • Windshield area is the same as factory and should fit most windshields without modification. The WelderD KRX4 Cage Kit is now available for one of the most capable sxs on the market!  The factory cage, like most other machines, lacks both safety and styling.  Our KRX4 Cage Kit will lower the roof line and produce a safer, better looking machine.  As with all our kits this KRX4 Cage Kit is made with .120 DOM tubing, bent, notched and ready to install on your machine by a qualified welder/fabricator.  Everything necessary to create a strong, safe and good looking aftermarket cage is provided with the kit – you just supply the welds! The KRX4 kit is available without options.  We’ve preselected the options for you to provide the strength and styling our customers expect.  All KRX kits are standard with 1.75 x 0.120 wall DOM main tubing.  Double B pillar and some bracing can be omitted if desired but will still be included.  If this kit doesn’t fit your needs please contact us to start the custom design process. Please download/print and review the directions for this kit below PRIOR to placing your order these will NOT be included with your shipment. Kawasaki KRX4 Cage Kit Directions FREE SHIPPING!
  • The WelderD KRX Kaos Cage Kit is now available for one of the most capable sxs on the market!  The factory cage, like most other machines, lacks both safety and styling.  Our KRX Kaos Cage Kit will lower the roof line and produce a safer, better looking machine.  As with all our kits, this KRX Kaos Cage Kit is made with .120 DOM tubing, bent, notched and ready to install on your machine by a qualified welder/fabricator.  Everything necessary to create a strong, safe and good looking aftermarket cage is provided with the kit – you just supply the welds! The Kaos is available in 2 options.  We have a 6.5” drop which gives a low streamline look but is too low for some riders so please check measurements before ordering.  Our 4.5” drop is for taller riders and those that want a better windshield fitment.  All WelderD kits are standard with 1.75 x 0.120 wall DOM main tubing.  Please download/print and review the directions for this kit below PRIOR to placing your order these will NOT be included with your shipment. *Pictures are of the 6.5” Drop Cage.  You can see the specific windshield photos in the Directions provided at the bottom of this page. Both versions will accommodate a windshield but the lower version may need some trimming for a more desirable look.  Pictures show a Factory Kawasaki glass Windshield. Please download/print and review the directions for this kit below PRIOR to placing your order as these will NOT be included with your shipment. Directions: KRX Kaos Cage Kit Directions We also provide a roof file below that can be sent directly to your local plasma/laser shop to cut for a perfect fit aluminum roof. KRX Kaos Cage Roof File.dxf FREE SHIPPING!
     
  • Fits all 2-seat 2014-current RZR XP 1000 and Turbo models. Does not Fit RZR S or RZR PRO. The WelderD RZR Elite WD Cage Kit is now available!  The factory cage, like most other machines, lacks both safety and styling.  Our RZR Elite WD Cage Kit will lower the roofline and produce a safer, better-looking machine.  As with all our kits this RZR Elite WD Cage Kit is made with DOM tubing, bent, notched and ready to install on your machine by a qualified welder/fabricator.  Everything necessary to create a strong, safe and good-looking aftermarket cage is provided with the kit – you just supply the welds! The Elite line is available without options.  We’ve preselected the options for you to provide the strength and styling our customers expect.  All Elite kits are standard with 1.75 x 0.120 DOM main tubing.  Double B pillar and some bracing can be omitted if desired but will still be included.  If our Elite line doesn’t fit your needs please contact us to start the custom design process or look at our other options for your RZR. Please download/print and review the directions for this kit below PRIOR to placing your order these will NOT be included with your shipment. RZR Elite WD Cage Kit Directions We provide a roof file below that can be sent directly to your local plasma/laser shop to cut for a perfect-fit aluminum roof. RZR Elite WD Cage Roof File.dxf  
  • The WelderD KRX Elite Cage Kit is now available for one of the most capable sxs on the market!  The factory cage, like most other machines, lacks both safety and styling.  Our KRX Elite Cage Kit will lower the roofline and produce a safer, better-looking machine.  As with all our kits this KRX Elite Cage Kit is made with DOM tubing, bent, notched and ready to install on your machine by a qualified welder/fabricator.  Everything necessary to create a strong, safe and good-looking aftermarket cage is provided with the kit – you just supply the welds! The Elite line is available without options.  We’ve preselected the options for you to provide the strength and styling our customers expect.  All Elite kits are standard with 1.75 x 0.120 wall DOM main tubing.  Double B pillar and some bracing can be omitted if desired but will still be included.  If our Elite line doesn’t fit your needs please contact us to start the custom design process. Please download/print and review the directions for this kit below PRIOR to placing your order these will NOT be included with your shipment. KRX Elite Cage Kit Directions We provide a roof file below that can be sent directly to your local plasma/laser shop to cut for a perfect fit aluminum roof. KRX Kaos Cage Roof File.dxf    
  • The WelderD Honda Talon 2-seat Cage Kit is now available!  The factory cage, like most other machines, lacks both safety and styling.  Our Honda Talon Cage Kit will lower the roofline and produce a safer, better-looking machine.  As with all our kits, this Honda Talon Cage Kit is made with DOM tubing, bent notched and ready to install on your machine by a qualified welder/fabricator.  Everything necessary to create a strong, safe and good-looking aftermarket cage is provided with the kit – you just supply the welds! We’ve preselected the options for you to provide the strength and styling our customers expect.  All kits are standard with 1.75 x 0.120 wall DOM main tubing.  If this cage kit doesn’t fit your needs please contact us to start the custom design process. Please download/print and review the directions for this kit below PRIOR to placing your order these will NOT be included with your shipment. Honda Talon Cage Kit Directions We also provide a roof file below that can be sent directly to your local plasma/laser shop to cut for a perfect fit aluminum roof. Honda Talon Cage Roof File.dxf
Go to Top